Measuring Equipment

PCE-DFG N 500 Force Gauge or Digital Force Gauge for pulling force and pressure gauge up to 500 N. PCE-DFG N 500 is the PCE-DFG N 500 digital force gauge for measuring force accurate with 0.1 N . resolution.

• Measuring range: 0 ... 500 N
  
• Accuracy: ±0.1%
  
• Memory for up to 100 measurements
  
• Measure traction and pressure
• Sampling rate 1600 Hz
  
• Interface: USB
  
• 6 different measuring tips
  
• Includes ISO Calibration Certificate.

PCE-DFG N 5K-ICA force gauge - Digital force gauge measuring both tensile and compressive forces with very high accuracy and resolution. This tensile and compressive force measuring device is commonly determined in a laboratory, e.g. to determine yield, breakaway force and force required to push a button or switch.

• Measuring range: 0 ... 5,000 N / 0 ... 1,124 lbs
  
• Resolution: 1 N / 0.22 lbs
  
• Accuracy: ±0.1%
  
• Memory stores 100 measurements
  
• USB interface
  
• Graphic display
  
• Includes ISO Calibration Certificate.

PCE-DFG NF 50K Force Gauge - Compressor with external load cell attachment designed to measure compressive forces at hard-to-reach measuring points. The probes have several threaded holes at the bottom allowing for a secure installation during measurement.

• Measuring range: 0 ... 50 kN / 50,000 N / 5,000 kg / 11,240 lbs
  
• Resolution: 0.5 N / 0.1 lbs
  
• Accuracy: ±0.5%
  
• Memory up to 100 measurements
  
• USB interface
  
• Graphic display
  
• Includes ISO Calibration Certificate.

Formaldehyde Meter - HAL Technology's HCHO toxic gas detector HFX205 is designed to detect formaldehyde in the air. The Formaldehyde Meter HFX205 indicates in situ formaldehyde concentrations thereby avoiding costly and time consuming analysis in laboratories. The Formaldehyde Meter HFX205 works with an electromechanical sensor and is designed to determine the allowable current limit. A measurement can be taken in less than 30 seconds.

• Formaldehyde range: 0…10 ppm
  
• Short reaction time
  
• Real-time display
  
• Manual and automatic data storage
  
• Hi-Speed USB
  
• Software for online data transmission.

Formaldehyde Gas Meter - The HCHO toxic gas detector HAL Technology's HFX205-100 is designed to detect formaldehyde in the air. The Formaldehyde Meter HFX205-100 indicates on-site formaldehyde concentrations thereby avoiding costly and time-consuming analyzes in laboratories. The Formaldehyde Meter HFX205-100 works with an electromechanical sensor and is designed to determine the allowable current limit. A measurement can be taken in less than 30 seconds.

• Formaldehyde range: 0…100 ppm
  
• Short reaction time
  
• Real-time display
  
• Manual and automatic data storage
  
• Hi-Speed USB
  
• Software for online data transmission.

The PCE-IGM 100-ICA Surface Check Gloss Meter is a test device for determining surface gloss. Thus, with a gloss meter, the spectral reflections of the light beam striking the surface to be measured are recorded and analyzed. The measuring device's touch screen allows for easy navigation.

• Geometry: 20° / 60° / 85°
  
• Measuring range: 20°: 0 ... 1000 GU / 60°: 0 ... 1000 GU / 85°: 0 ... 160 GU
  
• Standard: ISO 2813 / GB / T 9754 / ASTM D 523/ ASTM D 2457
  
• Light source: D65
  
• Wavelength: 400-700 nm
  
• Includes ISO Calibration Certificate.